230kw and 500nm
Little G60 Patrol
- grips
- Location: kathu
- Has thanked: 53 times
- Been thanked: 145 times
- Posts: 1178
- Joined: Tue Apr 03, 2018 5:08 am
How do you make a Patrol side shaft ? ............................You take a Cruiser shaft and cut it down in size.
Were impossible to find a H200 rear shaft in SA.
Took a shaft from a FJ 45 Cruiser cut and modified it on the lathe to fit the Patrol.
Cut the bearing housing to take a larger bearing and oil seal.
Were impossible to find a H200 rear shaft in SA.
Took a shaft from a FJ 45 Cruiser cut and modified it on the lathe to fit the Patrol.
Cut the bearing housing to take a larger bearing and oil seal.
You will never find me without Stroh or a 4x4
- david bfreesani
- Location: West Coast
- Been thanked: 1 time
- Posts: 156
- Joined: Sun Nov 11, 2018 8:45 pm
Amazing work, well done.
David vd Merwe
1997 2.7TD Nissan Sani SFA
150mm Lift, 33" rubber, dual transfer cases
1997 2.7TD Nissan Sani SFA
150mm Lift, 33" rubber, dual transfer cases
- Mad Manny
- Location: Johannesburg
- Has thanked: 458 times
- Been thanked: 937 times
- Posts: 6495
- Joined: Thu Mar 29, 2018 9:31 am
Flip, you dont break enough Drive and Side Shafts to be a child of Christo's...
"No one ever got stuck - in mid air!"
2010 Fortuner D-4D 4x4 'Fearless'
2006 Conqueror Conquest 'Gearless'
2010 Fortuner D-4D 4x4 'Fearless'
2006 Conqueror Conquest 'Gearless'
- CornellMans
- Location: Tshwane
- Has thanked: 12 times
- Been thanked: 6 times
- Posts: 232
- Joined: Tue Feb 11, 2020 1:39 pm
Sal nie omgee om so een te besit nie. Wens ek het die kennis, gereedskap, tyd, kapitaal en geduld gehad om so iets te bou. Knap gedaan Oom Grips
2018 Ford Everest 3.2 4x4 XLT AT
Wilderness 310
Wilderness 310
-
- Location: Ekurhuleni
- Has thanked: 72 times
- Been thanked: 146 times
- Posts: 1082
- Joined: Tue Jul 03, 2018 7:06 am
- Contact:
Hy het soos ons almal met n Kas Kar begin toe hy n Lighty was en Ronde Wiele op sy Kaskar gefit om vinniger te glideCornellMans wrote: ↑Mon Nov 08, 2021 8:13 amSal nie omgee om so een te besit nie. Wens ek het die kennis, gereedskap, tyd, kapitaal en geduld gehad om so iets te bou. Knap gedaan Oom Grips
toe fit hy sy 50cc se motor en dit was seker die "Turning" Point van ons Almal
Maar yes Grappie op n Stokkie
Ons almal het Verskillende Skills level
Grips se een is op Hoer Graad
Syncro Cox Camper
SJ 410 TarzanTiny
Millennium Beetle VR6 T Liberty
And a few VW Air cooled Toys
SJ 410 TarzanTiny
Millennium Beetle VR6 T Liberty
And a few VW Air cooled Toys
- grips
- Location: kathu
- Has thanked: 53 times
- Been thanked: 145 times
- Posts: 1178
- Joined: Tue Apr 03, 2018 5:08 am
This was a sideline project. The kids did most of the work. I only built the engine and the Land Cruiser H55 conversion. The rest of the project were completed by the kids.
Nice little 302 Ford V8 with Edelbrock alu heads and top end kit. Edelbrock claims 278kW and 462Nm. I bumped the compression and went for a more torque with a more 4x4 orientated cam. Think it is good for 230kw and 500nm.
PLan to install FJ45 Cruiser diff`s in the future.
https://www.edelbrock.com/performer-rpm ... -2091.html
Nice little 302 Ford V8 with Edelbrock alu heads and top end kit. Edelbrock claims 278kW and 462Nm. I bumped the compression and went for a more torque with a more 4x4 orientated cam. Think it is good for 230kw and 500nm.
PLan to install FJ45 Cruiser diff`s in the future.
https://www.edelbrock.com/performer-rpm ... -2091.html
You will never find me without Stroh or a 4x4