Looking for a Product or Service

[Wave]

Thank you, I need someone that can come and check / repair a door on a Smeg oven. The oven door doesn't close properly and I'm buggered if I can see how to adjust the hinges, if that's even possible.

If they can talk nicely (without using a big hammer) to the ice maker / dispenser on a Defy fridge that will be a bonus.

For obvious reasons, I need someone that can come to my house in Edenvale, Gauteng (both are damn heavy and I'm not going to take them anywhere).

Give Andy a call 082-870-1181 - he may be able to help, if not maybe he can point you in the right direction

[Erin]

Thanks Geoff, I'll give him a holler.

[Mad Manny]

I'm looking for a Home A/C Tiffy.

I have an LG Artcool Aircon. Installed in 2006.

If I use it on HEAT Mode it starts & goes to Defrost mode & stays there.
It's either the circuit, or the reverse valve or the sensor or board.
I spoke to the installer, but he just wants to replace the entire unit.

So someone who repairs Split unit Aircons (LG) in the West Rand area.

Thanks...

[BushWacker]

Have a 1975 Series 3 88” 2.25L petrol ...
... but chassis is not in very good condition and I want to patch/case/repair the main chassis rails between the wheel arches
... so/and to be done without removing the Engine, Bulkhead or Axles ...
... I will remove the cab and flooring and bodywork to expose the main rails ... fuel tank already removed.
... May be awkward but rails will be accessible from above and below ... nearly all welding will be from above .

Can anyone recommend a (preferably coded) welder that would/could do this sort of doctoring work ?

[Paul#25]

I have an AEG (Electrolux) deepfreeze that is not operating correctly. Can anyone recommend a good fridge repair guy to contact, preferably based in the East Rand. I can be contacted on zero 8 3 three 7 9 three 4 7 one.

[KurtG]

Hi guys, I’m hoping for assistance with my wheelbarrow.

I need the axle repaired, it seems the shaft has rusted through and it may need replacement, and I don’t want to pay more than the cost of a new Lasher from Makro.

Does anyone know a decent wheelbarrow repair centre in or around the northern suburbs of Johannesburg?

[Ricof4e]

Hi guys, I’m hoping for assistance with my wheelbarrow.

I need the axle repaired, it seems the shaft has rusted through and it may need replacement, and I don’t want to pay more than the cost of a new Lasher from Makro.

Does anyone know a decent wheelbarrow repair centre in or around the northern suburbs of Johannesburg?

Try gentler thrusts and lube next time.

[BushWacker]

Hi guys, I’m hoping for assistance with my wheelbarrow.

I need the axle repaired, it seems the shaft has rusted through and it may need replacement, and I don’t want to pay more than the cost of a new Lasher from Makro.

Does anyone know a decent wheelbarrow repair centre in or around the northern suburbs of Johannesburg?

... you could try Sweet Manny Malone
As he wheels his wheelbarrow
Through streets wide and narrow
Crying " axles and shackles , revived, aligned, oh ... “

[Leon]

Hi manne.
Ek soek tweedehandse bande vir plaas bakkie. As iemand het of weet van bande.
30/9.5 R15 of 245/70/15

[Martin de Jager]

Leon Ek het n baie mooi stel bande meer 75% lewe al vier bande sonder enige puncture of sidewall skade, 31x10.5x15 Brutus, r R7200,00 rerig goeie koop.

[Leon]

Martin dankie , maar hulle is net bietjie te groot.
Sal nog bietjie rond kyk eers.