Give Andy a call 082-870-1181 - he may be able to help, if not maybe he can point you in the right directionErin wrote: ↑Thu May 28, 2020 12:23 pmThank you, I need someone that can come and check / repair a door on a Smeg oven. The oven door doesn't close properly and I'm buggered if I can see how to adjust the hinges, if that's even possible.
If they can talk nicely (without using a big hammer) to the ice maker / dispenser on a Defy fridge that will be a bonus.
For obvious reasons, I need someone that can come to my house in Edenvale, Gauteng (both are damn heavy and I'm not going to take them anywhere).
Looking for a Product or Service
Forum rules
Please note that adverts are automatically deleted after 30 days
Please note that adverts are automatically deleted after 30 days
- Wave
- Location: Edenvale
- Posts: 510
- Joined: Thu Apr 05, 2018 4:23 am
Looking for a Product or Service
Geoff Craig
'09 Toyota Fortuner 3.0 D-4D 4x4
'10 Conqueror Comfort
'09 Toyota Fortuner 3.0 D-4D 4x4
'10 Conqueror Comfort
- Erin
- Location: Edenvale
- Posts: 77
- Joined: Tue Apr 03, 2018 7:10 pm
Thanks Geoff, I'll give him a holler.
- Mad Manny
- Location: Johannesburg
- Posts: 3585
- Joined: Thu Mar 29, 2018 9:31 am
I'm looking for a Home A/C Tiffy.
I have an LG Artcool Aircon. Installed in 2006.
If I use it on HEAT Mode it starts & goes to Defrost mode & stays there.
It's either the circuit, or the reverse valve or the sensor or board.
I spoke to the installer, but he just wants to replace the entire unit.
So someone who repairs Split unit Aircons (LG) in the West Rand area.
Thanks...
I have an LG Artcool Aircon. Installed in 2006.
If I use it on HEAT Mode it starts & goes to Defrost mode & stays there.
It's either the circuit, or the reverse valve or the sensor or board.
I spoke to the installer, but he just wants to replace the entire unit.
So someone who repairs Split unit Aircons (LG) in the West Rand area.
Thanks...
"No one ever got stuck - in mid air!"
2010 Fortuner D-4D 4x4 'Fearless'
2006 Conqueror Conquest 'Gearless'
2010 Fortuner D-4D 4x4 'Fearless'
2006 Conqueror Conquest 'Gearless'
-
- Location: Johannesburg
- Posts: 1025
- Joined: Tue Apr 03, 2018 6:27 pm
Have a 1975 Series 3 88” 2.25L petrol ...
... but chassis is not in very good condition and I want to patch/case/repair the main chassis rails between the wheel arches
... so/and to be done without removing the Engine, Bulkhead or Axles ...
... I will remove the cab and flooring and bodywork to expose the main rails ... fuel tank already removed.
... May be awkward but rails will be accessible from above and below ... nearly all welding will be from above .
Can anyone recommend a (preferably coded) welder that would/could do this sort of doctoring work ?
... but chassis is not in very good condition and I want to patch/case/repair the main chassis rails between the wheel arches
... so/and to be done without removing the Engine, Bulkhead or Axles ...
... I will remove the cab and flooring and bodywork to expose the main rails ... fuel tank already removed.
... May be awkward but rails will be accessible from above and below ... nearly all welding will be from above .
Can anyone recommend a (preferably coded) welder that would/could do this sort of doctoring work ?
... Famous Fiver VoorLoper ...
... Veni Vidi Vici ...
... Veni Vidi Vici ...
- Paul#25
- Location: Ekurhuleni
- Posts: 795
- Joined: Tue Apr 03, 2018 4:01 pm
I have an AEG (Electrolux) deepfreeze that is not operating correctly. Can anyone recommend a good fridge repair guy to contact, preferably based in the East Rand. I can be contacted on zero 8 3 three 7 9 three 4 7 one.
The humble person makes room for progress; the arrogant person believes they’re already there.
2004 Disco 2 Td5
2004 Disco 2 Td5
- KurtG
- Location: London
- Posts: 1890
- Joined: Fri Mar 30, 2018 12:52 pm
Hi guys, I’m hoping for assistance with my wheelbarrow.
I need the axle repaired, it seems the shaft has rusted through and it may need replacement, and I don’t want to pay more than the cost of a new Lasher from Makro.
Does anyone know a decent wheelbarrow repair centre in or around the northern suburbs of Johannesburg?
I need the axle repaired, it seems the shaft has rusted through and it may need replacement, and I don’t want to pay more than the cost of a new Lasher from Makro.
Does anyone know a decent wheelbarrow repair centre in or around the northern suburbs of Johannesburg?
Flex is overrated
- Ricoffy
- Location: Nambia
- Posts: 940
- Joined: Tue Apr 03, 2018 3:40 pm
Try gentler thrusts and lube next time.KurtG wrote: ↑Wed Jul 15, 2020 6:48 amHi guys, I’m hoping for assistance with my wheelbarrow.
I need the axle repaired, it seems the shaft has rusted through and it may need replacement, and I don’t want to pay more than the cost of a new Lasher from Makro.
Does anyone know a decent wheelbarrow repair centre in or around the northern suburbs of Johannesburg?
Knowledge is knowing that a tomato is a fruit.
Wisdom is knowing not to use it in a fruit salad...
Wisdom is knowing not to use it in a fruit salad...
-
- Location: Johannesburg
- Posts: 1025
- Joined: Tue Apr 03, 2018 6:27 pm
... you could try Sweet Manny MaloneKurtG wrote: ↑Wed Jul 15, 2020 6:48 amHi guys, I’m hoping for assistance with my wheelbarrow.
I need the axle repaired, it seems the shaft has rusted through and it may need replacement, and I don’t want to pay more than the cost of a new Lasher from Makro.
Does anyone know a decent wheelbarrow repair centre in or around the northern suburbs of Johannesburg?
As he wheels his wheelbarrow
Through streets wide and narrow
Crying " axles and shackles , revived, aligned, oh ... “
... Famous Fiver VoorLoper ...
... Veni Vidi Vici ...
... Veni Vidi Vici ...